Sub-Total: $0.00
Interactive Mounting Guide
Find Your Perfect Mounting Method
Not sure how to mount or measure for solar screens? Answer a few questions about your window, and we'll tell you what fits and how to measure for it.
← Back
Step 1: Check for Tracks
On the outside of your window, look at the top and bottom (or left and right sides) of the ENTIRE window frame (not just the bottom section). Is there an empty U-shaped channel or track?
← Back
Step 2: Is the Window Recessed?
Is your window set back into a masonry opening (Brick, Stone, Stucco)?
The Nickel Test: Can you place a nickel on the side of the brick surround in front of the window (at least 3/4" depth) without it hanging over?
The Nickel Test: Can you place a nickel on the side of the brick surround in front of the window (at least 3/4" depth) without it hanging over?
← Back
Step 3: Window Material
We are now looking at "Surface Mounting." What material is your window FRAME made of (not the trim around the frame)?
← Back
Step 4: Frame Width
Do you have at least 1/2 inch of flat, smooth frame surface on ALL FOUR sides of the window?
← Back
Step 5: Surrounding Trim
Is there flat TRIM (wood, hardie board, etc) surrounding the window frame itself?
← Back
Recommendation: Leaf Springs
Since you have tracks, this is the Gold Standard.
- ✅ Best seal against bugs.
- ✅ Cleanest look (no visible hardware).
- ✅ No drilling or adhesive required.
See Instructions Below:
In order to use leaf springs, be sure you have a track or channel at the top and bottom of the window frame (or the left and right side) for the solar screen frame to wedge into.
If you have tracks/channels on BOTH the left/right sides and top/bottom, then pick one set of tracks to use and ignore the other. You cannot fit a rigid screen in the top/bottom and left/right sides at the same time.
The following instructions assume your channel/tracks are at the top and bottom of your window.
Width - Measure from the inside edge of the recessed area on the left to the inside edge of the recessed area on the right - be sure to keep the tape measure level and straight. Measure in multiple locations and note the smallest measurement. Subtract ⅛” for clearance. Record this number as the width.
Height - measure from the INSIDE TOP of the recessed channel (yes all the way up inside the channel) down to the top of the bottom lip (NOT INSIDE the bottom channel) on the bottom channel/track. Subtract 1/8” for clearance (ignore the video that says 1/16"). Record this number as the height.
Go to SolarScreenOutlet.com and order the size and quantity of screens you need.
Assemble the screen according to the instructions above.
Insert the solar screen with the springs end in first and pop the opposite side in place.
80 Black/Bronze/Leaf Springs
80 Stucco/White/Leaf Springs
Start Over
← Back
Recommendation: Brick Clips
Perfect for your window recessed in brick, stone or stucco.
- ✅ Easiest install for brick/stone homes.
- ✅ Uses tension (no drilling or glue).
- ✅ Very secure.
- ⚠️ Leaves a 1/2" gap on each side of the solar screen
See Instructions Below:
Brick clips are perfect for most brick homes. Be sure you have a brick surround on the left and right sides (or top and bottom) of your window so the brick clips can grab the brick securely.
Width - measure from the inside edge of the brick frame on the left side to the inside edge of the brick frame on the right side. Measure in multiple places and note the smallest width. Subtract 1” to allow for clearance on each side for the brick clips. Record this number as the width.
Height - measure from the bottom of the brick frame to the top of the window frame. Subtract 1/8” for clearance. Record this number as the height.
Go to SolarScreenOutlet.com and order the size and quantity of screens you need.
Assemble the screen according to the instructions above.
Attach two brick clips on each side of the screen frame with the 2 holes on the back side of the frame, about 8” from the top and 8” from the bottom. Use clear tape to hold the clips in place if needed. Push screen in place so that the brick clips grip the bricks and hold the screen securely in place.
Start Over
← Back
You have great options!
Your window setup allows for our most popular surface mounts. Choose based on your priorities:
Option 1: 3M Dual Lock
Best for: Protecting Warranties & Cleanest Look.
✅ No Holes | ✅ Hidden hardware | ⚠️ Requires flat 1/2" surface on window frameOption 2: Casement Clips
Best for: Security and Traditional Fit.
✅ Very Secure | ✅ Easy removal | ⚠️ Requires drilling which may void your window warrantyReady to measure? Select your method:
How to Measure and Install Using Dual Lock
Be sure you have at least 1/2” of flat, smooth window frame surrounding all four sides of the window.
Width - Measure the window frame from the left outside edge to the right outside edge. Subtract ⅛” for clearance. Record this number as the width.
Height - Measure the window frame from the top outside edge to the bottom outside edge. Subtract ⅛” for clearance. Record this number as the height.
Go to SolarScreenOutlet.com and order the size and quantity of screens you need.
Assemble the screen according to the instructions above.
Thoroughly clean and dry the window frame to ensure proper adhesion of the 3M Dual Lock Pads.
Remove backing from one side of the 3M Dual Lock pair and attach to one corner of the back side of the solar screen frame.
Repeat for all 4 corners and for any additional locations you want to add the 3M Dual Lock.
Remove the backing from the 3M Dual Lock pairs that are now attached to the solar screen frame.
Attach the screen to the window frame and be sure to push and hold for 15 seconds on each location where the 3M Dual Lock pads are attached.
90% Black/White/Dual Lock
90% Black/Tan/Dual Lock
How to Measure and Install Using Casement Clips
In order to use casement clips, be sure you have at least ½” of flat window casement surrounding at least 2 opposite sides of the window (typically the top and bottom, but clips can also be placed on the left and right side).
Measure where you want to place the turn clips - about 6"-8” from top and bottom on each side.
Draw a circle where each casement clip will go - use a pencil eraser as a template.
Width - measure from the inside edge of circle on the left to the inside edge of the circle on the right. Subtract ⅛” inch for clearance. Record this number as the width.
Height - measure the entire height of the window frame and subtract ⅛” for clearance. Record this number as the height.
Go to SolarScreenOutlet.com and order the size and quantity of screens you need.
Assemble the screen according to the instructions above.
Set the screen in place to be sure it will fit.
Mount screen by screwing in turn clips using hex-head driver and self-tapping screws (included).
90 Gray/Champagne/Casement Clips
80% Stucco/Tan/Casement Clips
Start Over
← Back
Recommendation: Casement Clips or Direct Screws
Based on your window material or frame width, dual lock won't stick reliably. We recommend mechanical fasteners.
How to Measure and Install Using Casement Clips
In order to use casement clips, be sure you have at least ½” of flat window casement surrounding at least 2 opposite sides of the window (typically the top and bottom, but clips can also be placed on the left and right side).
Measure where you want to place the turn clips - about 6"-8” from top and bottom on each side.
Draw a circle where each casement clip will go - use a pencil eraser as a template.
Width - measure from the inside edge of circle on the left to the inside edge of the circle on the right. Subtract ⅛” inch for clearance. Record this number as the width.
Height - measure the entire height of the window frame and subtract ⅛” for clearance. Record this number as the height.
Go to SolarScreenOutlet.com and order the size and quantity of screens you need.
Assemble the screen according to the instructions above.
Set the screen in place to be sure it will fit.
Mount screen by screwing in turn clips using hex-head driver and self-tapping screws (included).
90 Gray/Champagne/Casement Clips
80% Stucco/Tan/Casement Clips
How to Measure and Install Using Screws
Coming soon...we apologize but we don't have instructions yet. Call us at 469-333-0215 or email us here for more info.
Start Over